Home > Products > Filter Element > Water filter element > PP melt-blow Water Filter Element with 10″20″30″40″

PP melt-blow Water Filter Element with 10″20″30″40″

PP meltblown filter elementsalso known as PP spunbond filter elementsare made of 100% FDA approved polypropylene materialfree of bindersadditives and lubricants.PP melt-blown filter element has large dirt holding capacitylarge flow ratelarge pressure dropgood chemical resistanceno fiber sheddinglong service life and good filtering effect.
 

General specifications

Quality:

Brand:DKFILTER

Filter material:Polypropylene

Sizes:L9.75″9.87″10″20″30″40″

End Caps:Polypropylene/no

Center Tube:Polypropylene/no

Seal:Siliconeethylene propylenefluororubber and nitrile rubber

Filter element surface:PP melt blown,fine graing,rooveem,bossed

Introduction:

PP meltblown water filter elements,also known as PP spunbond filter elements,are made of 100% FDA approved polypropylene material,free of binders,additives and lubricants.PP melt-blown filter element has large dirt holding capacity,large flow rate,large pressure drop,good chemical resistance,no fiber shedding,long service life and good filtering effect. PP spunbond filter element is an economical classic depth filter element,widely used in liquid pre-filtration industries such as industrial wastewater treatment,electronics industry,electroplating solution,petrochemical process,chemicals and solvents,RO/ID water filtration,seawater desalination, etc.


Features:

1. The deep hole groove structure on the surface disperses the direction of water flow and reduces the resistance of water flow.

2. The progressive density structure increases the dirt holding capacity of the filter element.

3. The surface fiber structure is strengthened, and it is not easy to cause hair loss

4. Made of PP superfine fiber, high filtration precision

5. 100% PP,high corrosion resistance

6. Formed by hot melt without adding any adhesive


Filter performance:

1. Filtration accuracy:1μm,5μm,10μm,20μm,50μm 

2. Maximum operating temperature:37.8℃

3. Maximum operating pressure:4.0 Bar

4. Due to different pore sizes,the flow rate per 10" filter element is between 3-10GPM

PP melt-blow Water Filter Element with 10″20″30″40″

....................................PP material flow characteristics


Technical Specifications / Component Materials:

1. Outer diameter:standard filter element 62mm,110mm,non-standard filter element can be produced according to customer requirements

2. Inner diameter:16mm,20mm,26mm,28mm,30mm,34mm,38mm,55mm,60mm,73mm,75mm,90mm,100mm,110mm

3. Length:9.75",9.87",10",20",30",40", 50",60"

4. Filter material:Polypropylene (PP)

5. End Caps:Polypropylene

6. Center pole:Polypropylene

7. Gasket:Silicone rubber,ethylene propylene rubber,nitrile rubber,fluororubber

8. Filter element surface:PP melt blown,melt blown fine grain,melt blown groove,melt blown embossed

PP melt-blow Water Filter Element with 10″20″30″40″


Application:

1. Used for people's livelihood drinking water filtration RO reverse osmosis filtration

2. Used for filtration of acid-base liquid in industrial chemical process

3. Filtration of industrial water and electroplating solution

4. Filtration of imaging liquid and ink

5. Pre-filtration treatment of sterile water and ultrapure water

6. Filtration of chemical raw materials and organic solutions


DKFILTER also offers a full range of replacement filter elements:

Parker

3M

Pall

Pentair

Peco

Other types are available on request

Related Specification Filters

Communication Requirements

© Copyright: 2012 Xiaoshan District, Hangzhou, Zhejiang Province, China Partner Environmental Protection Technology Co., Ltd.

payment methods